hey. i've got 4 usb ports in the back and 2 in the front of my dell desktop. how can i find out which are usb 2.0?
Where are my USB 2.0 ports?
I asked this on another forum some months ago. Aparently if you go the the System Properties, Click On The Hardware Tab, then select Device Manager. Then click on the plus sign next to the Universal Serial Bus Controlers list, if Enhanced Host Controller is displayed, you have USB 2.0.
The key word is Enhanced, aparently this means 2.0.
Hope that helps.
apparantly you did not read the question
WHERE are my USB 2.0 ports. i know they're there... the computer manual says so and so does device manager [checked before], but I need to locate them.
apparantly you did not read the questionWHERE are my USB 2.0 ports. i know they're there... the computer manual says so and so does device manager [checked before], but I need to locate them.
Sorry my friend, i was only trying to be helpful.
apparantly i went to dell support and ALL my USB busses are 2.0, yet when i plug an ipod in it says "please connect to a hispeed bus" hmm
are you saying that some of them are 2.0 and some of them are 1.1 and you need to find out which are which? they probably are all 2.0. i doubt they'd install non-forward-compatible 1.1's when 2.0 is backward-compatible. plug an external 2.0 drive into each port and see how fast the data xfers.
I don't know why, but I get that same message sometimes too. All of my usb ports are 2.0, yet sometimes when I plug something into them, Windows tells me that they aren't. It might be an issue within Windows XP, but I am not sure of this.
HAHAHAHAHAHAHAHAHHAHAHAHA
Pat on a Dull? ![]()
ROFL
Anyway, the front USB ports are usually 1.1 cause Dull cuts cost. However it's not always the case.
Back ports are probably USB 2.0.
Buy a Mac Pat, all of its ports are 2.0 ![]()
Or buy a USB2.0 PCI card for around $20. Then you'll know exactly which ones are USB2 compatible.Buy a Mac Pat, all of its ports are 2.0![]()
On that note, I heard of issues with iffy USB2 support after installing WinXp service packs. I myself have one port that changes from enhanced to normal when I put my computer in standby. But if I restart, everything works fine again.
I believe you have to pgrade to alteast sp1.
I have a dell as well the back ports are 2.0 certain things you plug in to the front usb will give that error so I plug my ipod in the back as well as my external drive. My mouse and keyboard are pluged into the front
Yes SP1 adds USB2.0, but I've heard SP2 makes the compatability a little shaky (like my situation).I believe you have to pgrade to alteast sp1.
I wonder if Dell motherboards have spare USB2 header pins?
Might be as simple as unpluging the cable for the front ports and plugging them onto different set of pins.
I wonder if Dell motherboards have spare USB2 header pins?Might be as simple as unpluging the cable for the front ports and plugging them onto different set of pins.
Don't do that if you don't exactly know what you do.
You can toast your motherboard if you do it wrong.
you do have to have sp1 for usb 2.0 support
Windows has had native USB 2.0 support since Windows 2000 Pro.
What kills it is third party or badly written OEM drivers.
My Adaptec USB 2.0 card in my old PC didn't require any additional drivers to run at full speed. This was before SP1 was even released.
The problem is proprietary motherboards like Dell, HP and a few others make.
They make it so you have to use their drivers. The generic one in W2k and XP meet industry standards... problem is, nobody frikkin follows standards.
Pat is dumb...dumb is pat...pat plays with a dell....pat touches his pee pee.
As said...depending on the cheap ass dell you got, they are either all 2.0 or just the backs....
Aqua-Soft Forums