Wheres my hardware?

Well, I'm very tempted to switch back to the PC side very soon (will prob keep the iMac of course). Reasons being most of the apps I've been using lately have either crashed every 5 seconds or just bloody slow.

Anyway what I want to know since I've been out of the loop for about a year now, whats a good cpu to aim for and motherboard. I'll be using it for webdesign and games of course. Stay with intel or go to the A64 line? Just not sure... help timmy out.

#261687

How much do you want to spend?

i recomend a 939 a64 with a NF4 motheboard. Something like the 3200 and the DFI NF4 motherboard. Webdesign can be done on a P3 so it doesnt realy amtter. The a64 kicks umm allot with games comapired to intel. right now intels kinda behind the pack and tryign to play ketchup.

If youd like to IM me id be more then willing to help out the funder behind the site that eats a large portion of my geeky life. Im well versed in modern hardware :P

#261706

How much do you want to spend?

i recomend a 939 a64 with a NF4 motheboard. Something like the 3200 and the DFI NF4 motherboard. Webdesign can be done on a P3 so it doesnt realy amtter. The a64 kicks umm allot with games comapired to intel. right now intels kinda behind the pack and tryign to play ketchup.

If youd like to IM me id be more then willing to help out the funder behind the site that eats a large portion of my geeky life. Im well versed in modern hardware :P

hehe...ketchup

anywho, i dont know a lot about motherboards, but definitly go for an AMD Athlon 64 4000+.

#261712

lostspyder knows whats up.

939 a64 3200 to 3500 is the sweet price/cpupower ratio right now (erm... well was about 3 weeks ago when i was looking). Above 3500 aren't worth the extra money when you look at how much more your paying for small cpu performance gains.

Unless you want a really high end gaming machine for games in the next year, since even a few games this last year show cpu-limiting when paired with highest end vid. cards at highest game settings. Kindof depends on the monitor you like to run (ie. high native resolution lcds).

Intel p4 = more money for same performance with lower efficiency (extra heat output/power suckage).

intel pentum-Ms look good but are overpriced (the motherboards are too).

#261720

3500 is looking tempting, I've been using asus mobo's the past few years, anyone want to recommend one now? Pci Express of course, and legacy free if possible :D

#261763

Well the only PCIe asus motherboar out now is the A8N. Its an SLI motherboard (uses two pcie cards in parell on one monitor to almost double the graphics preformance) though you can use one graphics card in it if you choose. pcie is brand new to AMD right now,, the only chipset that supports it is the nvidia nforce4 which came out a little before xmas. I personaly own an A8N and i kinda dont recomend it. I ran into a ton of bugs and i gotta do all these like tricks in the bios to get it to work the way it should. Allot of people have these problems with the board, but for allot of people the board works without a hitch, so it seems luck of the draw. If your willing to try out another MFG i recoemend DFI, but to each there own :P This persoanly will be the last asus MB i will ever build with.

A8N:

http://www.newegg.com/app/ViewProductDesc....-131-524&depa=1

DFI

http://www.newegg.com/app/ViewProductDesc....-136-152&depa=1

right now there are two variants of athlon 64s, the 120nm and the 90nm. There is little difrence at stock besides the 90nms run a little bit cooler, but if you plan on overclocking at all buy a 90nm without question.

Also make shure to get two sticks (for dual chanel) of good low latency memory. The clock speed on the memory isnt so important with the a64 like it was with the athlon or the P4. Because the memory controller was taken off the northbridge and put onto the CPU, it has a very low latency (that is time it takes for a signal to go from the CPU to the memory and back) so thoes memory timmings will be where you will get most of your preformance.

Somehting along these lines

http://www.newegg.com/app/viewproductdesc....-145-450&DEPA=1

#261847

I would actually say, go for the S754 if you want an AMD64: The biggest difference is the dual-memory channel vs. single memory-channel on the S754 and benchmarks show that a dual-memory channel doesn't have a real impact on performance mainly because of the HyperTransport thingy. Only if you are a real rich kid, go for the S939, 'cause the S754 cpus are much cheaper ;)

#261849

He is a rich kid, thats the problem :slant:

#261851

I would actually say, go for the S754 if you want an AMD64: The biggest difference is the dual-memory channel vs. single memory-channel

Yeah that and the fact that 754 is a dead socket. I doubt that a year from now AMD will be releasing faster s754s. Also theres the whole chipset thing where nf4 is for the 939 platform only afaik and with nf4 comes PCIexpress (SLI included) and sata2. And considering that the diffrence between the 754 3200 and the 939 3200 is 1$ at newegg, your only real cost benifit is in the MB, and considering that he wants asus (not exactly value market oreintated)......

#261862

oooh you americans are so lucky. Price difference is here around 40 euros in the cpu's and yet, you still have to buy a cpu-cooler for the 939. Also, S939-mainboards are much more expensive here.

#261868

oooh you americans are so lucky. Price difference is here around 40 euros in the cpu's and yet, you still have to buy a cpu-cooler for the 939. Also, S939-mainboards are much more expensive here.

Id happly take a price diffrence in 754 to 939 cpus then be under the leadership of bush any day :P

Is that 939 a 130nm(newcastle) or a 90nm(winchester) cause like i said before the 90nms are more expensive.

#261880

Hmm speaking about that ^ can someone explain why say on newegg the 3400 is only like 20$ more than the 3200, when the 3500 is almost 80$ more.

When the 3400 is 2.4 and the 3500 is 2.2 :S confusing crap now. And whats that .90 stuff? :$

#261892

When the 3400 is 2.4 and the 3500 is 2.2 :S confusing crap now. And whats that .90 stuff? :$

Hehe you used to be an intel fanboy didnt you. All worried about the clock speed.

the 90nm (called winchester vs newcastle for the 130nm) is the size of the tiny little transistor gates inside of the CPU. The smaller the gate, the less voltage it takes to activate (or equivlent force for push electrons though it) the less heat it generates.... etc. Smaller is better, though doesnt nescarly yeild a speed increase at the same clock speed assuming that the cpus are ideintical besides gate size. The 90nm cpus also have a new memory controller on them (only marginaly faster)

#261907

Ok, another thing, what about cases... I used to have the Antec Sonata (and if all else fails I'll just get another one of those), I need a case that is not one of those cheap plastic ones with a window, but one that is well build (mid tower or smaller), and is silent, it will be on the top of my desk so quite is a must :$.

Any suggestions.

#261924

Ok, another thing, what about cases... I used to have the Antec Sonata (and if all else fails I'll just get another one of those), I need a case that is not one of those cheap plastic ones with a window, but one that is well build (mid tower or smaller), and is silent, it will be on the top of my desk so quite is a must :$.

Any suggestions.

Cases are tough because it all kinda comes down to a matter of what you think looks the best and how much you want to spend.

Mabie a nice sexy, well built and sleek lianli case?

http://www.svc.com/ca-pc61-99.html

also you might want to peek at some SFF setups (ie a 'shuttle') if its going on top of your desk.

#261927

no offence but i think that case is ugly. i may be getting a new case for my pc and i'm deciding between a nice acrylic case or a nice window one with an lcd temperature display and color changing lights.

#262465

the case isn't bad in my opinion.

definitely go with 939 pin instead 754. though the performance in terms of megaflops may be negligible, the memory performance difference is astonishing.

myself, i have been having problems with asus's boards, so i am probably gonna stay away from there for some time too.

#262468

TheSmallB you are crazy, that case is simple, sexy and none of that plastic **** to go on the side.

Ok almost one of my last few questions lol.

Which to get the a3200+ 90nm one or the 3400+ 13micron one?

#262509

I'm also stumped about 2 motherboards, MSI or DFI

MSI K8N Neo4 Platinum or the DFI NF4 Ultra-D

And is it worth the extra 50$ to get the SLI versions of these boards?

#262677

Well get the 90nm one if you plan on overclocking. If you are not planing on overclocking get the 130nm one as its faster at stock speed.

I think of thoes two the MSI might be a bit better becasue instead of using a standard onboard sound solution it uses soundblaster live. Better preormance while gaming. review of the two: http://www.anandtech.com/mb/showdoc.aspx?i=2358&p=21

Spend the extra 50$ for SLI only if you plan on buying a second graphics card to SLI the two. If you think this is likley go for it. Its kinda like a payment plan on upgrading, get one card now, and when the card you buy now halfs in price in 7 months buy a second :P Otherwise there is no diffrence realy. Infact a non-sli NF4 chip can be easily modded into a SLI chip.

#262755

isn't the 130 pretty much dead though?

I'd like to have that freedom of upgrading in the future, I also found a different mobo,

DFI "LANPARTY UT nF4 Ultra-D" NVIDIA nForce4 Ultra Chipset Motherboard For AMD Socket 939 CPU -RETAIL

Thoughts on that?

#262814

Its a very good motherboard.

Also the nm only realy refers to the CPU, it doesnt realy have anything to do with upgradablility. Perhaps you should just ignore that stat for the time being :P i may have been getting too indebth by brining it up. The one that you should be conecerned with is the socked, either 754 (dying) or 939 (alive and in good health)

Make shure to pick up a decent power supply though. Somehting from antec or thermaltake (i cant belive im recomending them) should be good. You dont have to go dumping 150$ + on a PSU but around 50$ should be good. Allot of people get a cheap PSU and half the time it works fine, but the other half it causes big problems.

Good PSU list

http://forums.extremeoverclocking.com/show...3&postcount=197

that superflower one though on the top of the list (cheapest) while is a good PSU requires some work, you have to open up the PSU, and adjust a potentiometer in there to get the voltages to the proper level. When i got one the computer woulnt boot to windows cause the voltages were too low, it was an awsome PSU after i adjested it though. It has an awsome feature set.

what a name hu "superflower"? is it "flow' like a river flows or flower as in the plant

What video card are you looking at?

and what are you doing with your mac?

#262836

Opening a PSU? Sounds dangerous lol.

Videocard - Msi (or any other brand that is better) 6600GT Pci-e

I'm just gonna slide my imac over and put the pc where its at, I'll use both of course, I'd rather use the imac for email and important crap.

BTW know anything about a 24pin connector, I read a few posts at Hardocp people complaining they don't have a 24pin connector which is needed to power the mobo.

#262849

Opening a PSU? Sounds dangerous lol.

Videocard - Msi (or any other brand that is better) 6600GT Pci-e

I'm just gonna slide my imac over and put the pc where its at, I'll use both of course, I'd rather use the imac for email and important crap.

BTW know anything about a 24pin connector, I read a few posts at Hardocp people complaining they don't have a 24pin connector which is needed to power the mobo.

Opening a PSU isnt terrably dangerious, as long as you pay attnetnion to what you touch. There is 120ac going in and there is a big ass filter capasitor on the magnitude of milifarads (in EE classes we refer to these as a "infinite capasitor") that hold a ton of charge. Other then that its preaty much harmless.

Ekkk i almost forgot about the 24 pin connector issues. Basicaly 24 pin (new standard) is a 20 pin (has been the standard the last few years for ATX) with 2 rows of 2 extra pins on one side of it. Its realy not diffrent at all (save voltage levels, just extra wires to carry the power), uses the same rails and everything. You can buy an adapter for a 20 pin or ive heard that you can even just use a 20 pin and say screw the extra pins also. I imagine the reason for switching to 24 pin is because CPUs and such are eating up so much more power, the extra wires can carry more amperage to supply that power, though im not realy shure.

A cheap PSU with a 24 pin connector will be a hard find, its generaly a feature on new, good PSUs. If your lookiing to dump about 80$ into a realy nice one i recomend an OCZ powerstream, im using one right now, its fantastic. It has a 24 pin connector.

MSI is a good brand. They make well designed products, at very nice prices

#262862