[help] Installing My New Sata Drive

hey,

i just got my Maxtor Diamondmax9 80gb SATA Hard drive. I put it in the second bay, and hooked up both cords (power, connection) When i start the computer, it just loads to my old 20gb samsung like normal, and in my computer there is no 2nd drive. How do i install my SATA drive without ruining my samsung drive with all the data on it? the HD

came by itself with no maunals or disks so i dont have a driver cd. Please help

Thanks,

Pops

#206706

check the jumpers again, power and ATA cables..

Does SATA work in ATA computer...

You might need anouther HD controller

#206715

ok everythings in check (SATA doenst require jumpers, its automatic)

btw, my model number is 6y080m0

whats a HD controller?

#206724

Which OS are you running? You may need to install drivers for it.

#206734

Motherboard make and model? Does the drive detect in the bios (step #1). Have you tried correcting everything suggested on the MAxtor site specifically relating to your drive?

#206735

Sometimes SATA drives can get a little tricky. If you're using Windoh XP, you have to install drivers for it. I have the same HD and i use Silicon 3112, the ones that came with the HD. I have always installed the drivers when installing XP, but they should work after installing too.

Edit. Weird enough, version 3112 of the drivers work for me, but 3114 dont :blink:

#206737

Most likely its a jumper issue on your HD. Still, for fun:

# Faulty Data Cable

The BIOS will not detect a hard disk if the data cable is damaged or the connection is incorrect. Maxtor recommends using UDMA cabling with a maximum length of 18 inches. UDMA cables have color coded connections which require proper orientation when connecting. The blue connector always connects to the motherboard. The gray middle connector is used for slave devices on the cable. The Black connector is used for Master device connection. Always inspect the motherboard, and hard disk connections for bent or misaligned pins. Folding, crimping, pinching, or creasing data cables can cause the wires to break inside the insulation, leaving the exterior of the cable looking normal. When in doubt of data cable condition replace it.

Picture of an Ultra ATA data cable.

# No Power to drive (drive is not spinning up)

If the drive is not receiving power or an incorrect level of power (12v) it will not spin up. To check to see if this is the cause of the BIOS not detecting the hard drive follow these steps.

1. With the system turned off, open the computer case and remove the data cable only from the hard drive. This will stop any “power saving” commands from being sent to the drive.

2. Turn on the system. Check to see if the hard drive is spinning. If you touch the side of the drive you should feel a slight vibration. If you do not hear or feel the hard drive spinning you will need to find out if the drive is getting power.

If the drive is not spinning please visit the Warranty Information Page.

# Incorrect jumper settings on the drive

If the Master / Slave jumper configuration is set incorrectly the drive may not be detected by the BIOS. Please consult the Jumper Setting Page for further instructions.

# BIOS Limitations (Capacity of drive is too large for the BIOS to support)

Computer systems built prior to October of 1998 typically hang or freeze while auto detecting large hard disks during system startup. Common BIOS capacity barriers include 528 MB, 2.1 GB, 8.4 GB, and 32 GB. There are multiple solutions to work around BIOS capacity barriers, always disconnect the ATA and power cables first before entering the BIOS, to keep the system from hanging.

To troubleshoot this problem follow these steps.

1. Restart and enter the system BIOS to set the drive parameters manually. (Entering the system BIOS is usually accomplished by pressing F1, F2, or DEL right after powering the system on. Look for an on-screen message stating which key to press.)

2. Set the BIOS parameters for the drive from Auto-Detect to None, or Off.

3. Save settings, exit setup, and power the system off.

4. Save BIOS settings and exit.

5. Reconnect the power and ATA cables, power the system on and boot to the MaxBlast CD or Floppy.

6. When the system boots to the MaxBlast program, choose the Utilities option and select Set Drive Size.

7. MaxBlast will register the maximum LBA the system BIOS can accommodate. Agree to the recommended settings MaxBlast has supplied, and finish the process.

8. Restart, enter the system BIOS, and set the drives parameters back to Auto-Detect.

9. Save settings, exit setup and reboot to the MaxBlast CD or Floppy and run the normal install. When finished partitioning and formatting the drive, follow the instructions to install Windows.

Alternate Settings: Steps 1and 2 above will not work on some system BIOS’s. This will be noticed by the system still hanging at startup or MaxBlast being unable to detect the drive after the BIOS has been set to none.

1. Try setting the drives parameters to a User Definable Type with 1024 cylinders, 16 heads, 63 sectors.

2. Set the LBA to Normal, Standard or Disabled, Write Pre Comp (WpCom) and Landing Zone (LZ) settings; can be set to zero.

3. Save settings, exit setup, and power the system off.

4. Reconnect the power and ATA cables, power the system on, and boot to the MaxBlast CD or Floppy.

5. Perform the MaxBlast normal install without using the set drive size feature.

If MaxBlast doesn't detect the drive and you followed all the troubleshooting steps above you may need contact your motherboard manufacturer for a BIOS upgrade or purchase an Ultra ATA PCI adapter card. Maxtor's online store, www.MaxStore.com, offers a complete line of Ultra ATA PCI cards that provides support for large capacity drives.

# Faulty Hard Drive If after all the above checks and procedures have been performed, you are still having trouble installing the drive, or O/S. It is recommended to run the PowerMax, drive diagnostic utility, to determine if the drive is defective. If PowerMax returns an error code please proceed to the Warranty Information Page.

https://maxtor.custhelp.com/cgi-bin/maxtor....gcitxLjh&p_lva=

#206739

ok, i actually switched on a setting in bios,my samsung drive detected the other drive and installed all the SATA RAID components from the floppy, but, the drive wont show up in my computer, and how do i make the drive bot first so i can install an OS on it?

#206801

I've always had troubles getting it to be the master drive, so here's my solution (not the ideal way, but hey, it works :P ):

I just unplug my other HD and then install windows. Since the Sata drive is the only one connected, XP recognizes it as the main boot device. After i've installed Windows, i just connect my other HD :P

#206803

hmmmm, that works. but there isn't like a special RAID screen where you could change settings, or does it show up now in the normal bios boot list?

#206806

I take that you mean how to make the SATA drive as the first boot device.

In the list of bootable devices (in your bios) there should be Serial-ATA, choose it and you're good to go.

#206814

It depends on your motherboards Bios. I was able to just plug in my SATA and install - it showed up in the Bios and under Windows XP. Unfortunatley Ive heard similar stories to yours from friends of mine using different motherboards. :(

#206815

well i tired doing the boot selection, no luck. tried unplugging the ide HD and booting from the SATA, but all i got was a blinking cursor. i even tried putting the xp disk in to install but it said there wernet any HD's. i notcied in disk management thers was a convert drive option to make my drive dynamic. should i do that? will that help make things work? what else can i do?

Pops

#206837

You probaly havent formated it yet. Easy. Go to controll pannel>administrative tools>computer managment.

Click on the 'disk managment' option on the right. On the bottom it will show all the avalable drives, (Take a screenshot of this if it doesnt work, and post) Right Click on the one that doesnt have a white thing with drive information, and chose format.

background- a hard drive comes completly bare, nothing on it usualy, all zeros. The operating system basicaly writes a table of contents at the begining of the drive, so it knows where everything is.

#206848

ok i formatted it, i tired to install wondows on it and i still got the "drive not present" error, then it quit. i know i have the drivers for it though. what should i try now?

#206857

For installing widnows on the drive, you have to have a floppy disk durring the instalation that has drivers for your specific RAID controller. What do you have the physical SATA cables plugged into, a motherboard, or a PCI card, and whats the speccific model/manafacture of the MB/PCI card?

#206889

ok i have the cables plugged into the raid 0 port on the motherboard. Manufacturer is MSI, it is a KT6 Delta Standard ( vt8232 chipset)

it came with a floppy called VIA RAID DRIVER. i installed it on the windoes side, is that the one i put in after i hit f6 in windows setup?

#206892

Originally posted by popsandthefamily@Aug 25 2004, 01:08 AM

ok i have the cables plugged into the raid 0 port on the motherboard. Manufacturer is MSI, it is a KT6 Delta Standard ( vt8232 chipset)

it came with a floppy called VIA RAID DRIVER. i  installed it on the windoes side, is that the one i put in after i hit f6 in windows setup?

<{POST_SNAPBACK}>

Thats exactly the one. Hit F6 at startup, after a minut or two it will finialy ask you for it, put it in and select the right driver. After that, you should be able to install windows to it easy as keca. :rock:

#206901

alright, im tired so i'll try it first thing tomorrow. is it ture that it has to NTFS? cause i want to transfer all my files (fat32) from the old to the new HD

#206912

IDK why it would have to be NTFS, and dont think thats true. No reason not to use NTFS, the only backwards compatability issues you will have is if your trying to use an m$ OS before windows 2000 (ie windows ME,98 or 95) or linux, besides that files will trasfer fine, defragmenting is a thing of the past too and indexing is nice.

#206927

hmm it only gave me the option of ntfs, and i did the raid driver and stuff, i did a quick nfts format, i came back upstairs later and it had restarted to my other HD, did a quick check and the RAID drive isnt recognized again, giving me the drive cant be found error. this is driving me nuts.anything else i havent tried? would reinstalling hte drivers from the floppy do it?

#206955

Set up in your BIOS to boot from the SATA drive, its probaly still trying to boot from your IDE hard drive which you probaly removed (IE the hard drive not found error)

If youve already done this, fiddle with the options a little, ofter there a little finicky. Bet your happy you got a sata drive hu? :smartass:

edit: if the HD is already formated as FAT you could install to it, but giving the option of formating a FAT partition would be 100% stupid, that would be like giving the option to take all of the stuff that makes XP good, and using the windows ME kernel during the install...

#206958

ok, i removed the IDE HD, then i set up my bios to do CD first, then the SATA HD, then nothing else. I also put no for boot other devices. Windows disk is in and still gives me the disk not found. i plug my IDE HD back in and go to disk management and it says the RAID drive is online and it is NTFS. my friend just got a new Maxtor 60gb IDE hd, im havinh him bring his disks with him to see if his maxblast will set up my HD. Could the HD be bad already? Or do i just need to boot the drive from that floppy with thr RAID drivers again and repair the partition?

EDIT: i have maxblast 3 and it detects my HD when i try to set it up, there are 2 options

1 - add the drive as an additional storage device

2 - add the drive as a new boot device

what should i check, if any?

EDIT AGAIN: doing #2 above is risky and form what i have heard can make noth drives not work, so i need to try something else.

#207117

first u need to do is

+ set cdrom to boot first, then install windows xp, when the xp install screen pop up just press F6, then xp instalation will ask u for driver cd for ur raid, usually supplied with the mainboard driver cd, copy it to diskette and u r done

+ to boot from sata all u need to is set the 1st boot to RAID in the bios setting

thats all ...

hope that help

#207473

If your installing data to the disk, its not bad. Its a problem with booting in the BIOS, ill bet you my left big toenail it is.

#207477